![]() Now, when I make the call between a softphone on the 10.23.0.0/24 network to a softphone on the vpn, the call works just fine. However, when I place the call from Jabber on my iPad (from vpn) on 10.22.1.0/24 network, the remote site cannot hear me, but I can hear them. When I place a call from either Jabber or IP Communicator (From VPN) on 10.22.1.0/24 network to an IP Phone on 10.23.32.0/24 network I have no audio. that passes fine according to the packet trace on the ASA. I am able to packet trace UDP with the port numbers that Wireshark says I'm using. I've been on with TAC to ensure my routing is correct. I suspect I have an issue in my firewall. We must ensure that all voice and 3389 traffic goes over MPLS WAN and all other traffic hits site to site vpn, for intersite traffic. We have Int 0/0 on mpls 2821 router split into sub-interfaces so that the CORE can send all traffic to it for PBR Routing, and send back any traffic that needs to hit site to site vpn. Softphone -> SSL VPN -> ASA 5510 -> Cisco 4507 CORE -> Cisco 2821 MPLS Router -> MPLS Network -> Cisco 2811 H.323 Gateway -> Cisco 2960 POE Switches -> Cisco 7942 IP Phone I'll do my best to describe the scenario: The phone is now setup and ready to use with your Vonage Business extension.I'm at a loss here, so any assistance will be very much appreciated. Click the X at the top left of the Preferences window to return to the main screen.Under the Other section uncheck Enable inactivity timers. Select the Call menu from the top of the screen.The only codec that should remain under the Enabled Codecs column is G711 uLaw. Use the < button to move all codecs except G711 uLaw to the Available Codecs column on the left. Select the Codecs menu from the top of the screen and then click the Audio Codes tab.Click on the Advanced tab under the Accounts menu and make the following changes:.Under the Firewall Traversal section verify that the None radio button is selected. Click the Topology tab under the Accounts menu.Enter *99 into the Number to dial for checking voicemail field. Click the Voicemail tab under the Accounts menu.Domain: :5060 (XXXXX is your Vonage Business account number).Uncheck the IP/Presence box under the Use for section.Select the Accounts menu from the top of the screen and click the General tab.click Account Settings from the main menu to access the Preferences menu. The phone is now setup and ready to use with your Vonage Business extension. Click OK at the bottom right of the screen to confirm all changes.Use the < < button to move all codecs except G711 uLaw to the Available Codecs column on the left. Select Audio Codes from the left navigation pane.Click Softphone, then Preferences from the main menu.Click OK at the bottom of the page to confirm all changes.Uncheck Send SIP keep-alives under the Connection Management section.Under the Register Settings section change Reregister every to 30 seconds. ![]() Click on the Advanced tab and make the following changes:. ![]() It is a stripped down version of Bria 4, an excellent softphone client, but it still comes with a good selection of features, including voice and video calls, messaging and presence. Verify that the Domain radio button is selected in the Domain Proxy section, X-Lite offers an excellent solution for people who wish to get used to softphones.Domain: :5060 (XXXXXX is your Vonage Business account number).Enter the following information in the User Details section that you documented when you added the softphone to an extension in your Online Account:.NOTE: Marking the option for IM/Presence results in audio quality issues or loss of registration. Uncheck the IM/Presence box under the Allow this account for section.Open X-Lite, then click Account Settings from the Softphone menu.Download and install the X-Lite Softphone. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |